Products
FAW Truck Brake Valve with Pipe Joint Assembly and Pedal 3514010-D9860W
  • FAW Truck Brake Valve with Pipe Joint Assembly and Pedal 3514010-D9860WFAW Truck Brake Valve with Pipe Joint Assembly and Pedal 3514010-D9860W
  • FAW Truck Brake Valve with Pipe Joint Assembly and Pedal 3514010-D9860WFAW Truck Brake Valve with Pipe Joint Assembly and Pedal 3514010-D9860W
  • FAW Truck Brake Valve with Pipe Joint Assembly and Pedal 3514010-D9860WFAW Truck Brake Valve with Pipe Joint Assembly and Pedal 3514010-D9860W
  • FAW Truck Brake Valve with Pipe Joint Assembly and Pedal 3514010-D9860WFAW Truck Brake Valve with Pipe Joint Assembly and Pedal 3514010-D9860W

FAW Truck Brake Valve with Pipe Joint Assembly and Pedal 3514010-D9860W

Model:3514010-D9860W
The FAW Truck Brake Valve with Pipe Joint Assembly and Pedal 3514010-D9860W is an OEM-standard dual-circuit pneumatic foot brake treadle valve module engineered specifically for FAW Jiefang heavy-duty commercial trucks, long-haul tractors, and dumpers. Supplied directly from Shandong, China—the core manufacturing and export hub for FAW Jiefang pneumatic braking and cabin control spare parts—this complete ready-to-install assembly integrates the floor-mounted brake pedal treadle, dual-circuit proportional air valve body, and pre-fitted pneumatic pipe joints into a single unit for precise, responsive braking modulation across front and rear axle service brake circuits. International B2B buyers, commercial fleet air-brake workshops, and regional spare parts distributors can request a wholesale quotation (RFQ) starting from a 1-piece sample trial order up to bulk carton or palletized container wholesale procurement, backed by a 6-month warranty and 3 to 7 days fast dispatch.

    Parameter Specification
    Product Name FAW Truck Brake Valve with Pipe Joint Assembly and Pedal / Dual-Circuit Foot Brake Treadle Valve
    Part Number / Model Number 3514010-D9860W
    Vehicle Brand & Truck Compatibility FAW Jiefang Series Heavy-Duty Commercial Trucks, Tractors & Dumpers
    Assembly Configuration Complete Foot Brake Pedal Treadle + Dual-Circuit Pneumatic Brake Valve + Pre-Fitted Pipe Joint Assembly
    System Category Heavy-Duty Commercial Vehicle Pneumatic Service Brake & Cab Control System
    Product Purpose Fleet Air Brake Maintenance, Foot Valve Replacement & Cab Pedal Repair (replace/repair)
    Product Condition 100% Brand-New OEM Standard (New)
    Warranty Coverage 6 Months Manufacturer Warranty
    Quality Standard Fully Guaranteed, Bench-Tested Dual-Circuit Pressure OEM Standard
    Place of Origin Shandong, China
    Minimum Order Quantity (MOQ) 1 Piece (Sample Trial Orders & Bulk Wholesale Supported)
    Single Package Size 25 x 20 x 30 cm
    Single Gross Weight 8.0 kg
    Standard Packaging Dust-Capped Protective Poly Bag, Molded Foam Bracing & Neutral Export Carton Box
    Payment Terms T/T (Telegraphic Transfer), Westunion (Western Union), PayPal, MoneyGram
    Delivery Lead Time Fast Dispatch within 3 to 7 Days

    Packaging, Logistics & B2B Wholesale Procurement

    • Direct Factory Wholesale & Flexible MOQ: Sourced directly from our Shandong OEM supply base to eliminate middleman markups, offering competitive tiered wholesale pricing for distributor bulk orders alongside a 1-piece MOQ for urgent fleet workshop repairs or sample evaluation.

    • Export-Ready Contamination-Free Packaging: Each 8.0 kg brake valve and pedal assembly is fitted with protective dust caps across every pre-installed pneumatic pipe joint, wrapped in a moisture-barrier poly bag with shock-absorbing foam inserts to protect the pedal hinge and fittings, and packed inside a reinforced 25 x 20 x 30 cm export carton box (consolidated onto wooden pallets for bulk sea freight).

    • Fast Global Dispatch & Multi-Modal Freight: Ready-to-ship warehouse stock enables fast order fulfillment within 3 to 7 days, supporting urgent air cargo dispatch for grounded fleet trucks as well as LCL/FCL ocean container consolidation alongside full-line FAW Jiefang, Sinotruk, and Shacman relay valves, four-circuit protection valves, brake chambers, and cab control spare parts.

    • Flexible International Trade Terms: Supports standard B2B procurement workflows with T/T, Western Union, PayPal, and MoneyGram payment options, complete with commercial invoices, packing lists, and export customs documentation.

    Operating Mechanics & Dual-Circuit Pneumatic Treadle Modulation Dynamics

    Heavy-duty commercial vehicles require progressive, fail-safe braking control that scales delivered air pressure smoothly with driver pedal effort while maintaining circuit independence between front and rear axles. The FAW truck brake valve with pipe joint assembly and pedal 3514010-D9860W acts as the primary driver-operated command valve mounted on the cab firewall/floorboard.

    When the driver depresses the textured foot pedal treadle, mechanical plunge force compresses a calibrated rubber/spring graduating element inside the upper housing, pushing down the primary and secondary relay pistons in sequence. This opens inlet poppet valves to meter compressed air from the primary (rear axle) and secondary (front axle) air reservoirs proportionally into the delivery pipe joints—delivering smooth, linear braking deceleration from light speed trimming to full emergency stops. When the pedal is released, internal exhaust ports open immediately to vent brake line pressure rapidly for crisp brake release without drag, while independent upper/lower chambers guarantee that if one brake circuit loses air pressure, the remaining circuit continues to operate mechanically.

    Precision Die-Cast Valve Metallurgy & Heavy-Duty Pedal Engineering

    Cab-floor foot brake valves endure millions of actuation cycles, wet/muddy driver boots, high pneumatic operating pressures (8–12 bar), and continuous cab vibration:

    • Pressure-Tight Die-Cast Aluminum Alloy Dual-Chamber Body: Precision CNC-bored dual-circuit valve casting engineered for zero porosity, smooth piston travel, and accurate port alignment with pre-installed factory pipe joints.

    • Anti-Slip Die-Cast / Reinforced Steel Pedal Treadle & Hardened Pivot Pin: Heavy-duty ribbed foot pedal paired with a hardened steel fulcrum pin and lubricated bronze/polymer bushings to prevent lateral pedal wobble or hinge seizure under heavy boot loads.

    • Oil- & Cold-Resistant NBR / Viton Piston Seals & Poppet Valves: High-durability elastomeric seals and vulcanized poppet seats formulated to resist compressor oil carryover and sub-zero stiffening (-40°C to +85°C) for airtight zero-leak sealing.

    • Pre-Installed OEM Pipe Joint Assembly & Protective Rubber Boot: Factory-torqued brass/steel pneumatic pipe fittings and a flexible dust boot shield the upper plunger mechanism from cab floor dirt, water, and grit.

    Fleet Troubleshooting & Foot Brake Valve Failure Diagnostics

    A leaking, sticking, or slow-venting foot brake valve compromises stopping response, drains air reservoirs, or causes dragging brakes. Fleet mechanics and air-brake technicians should inspect or replace the 3514010-D9860W brake valve and pedal assembly upon detecting:

    1. Continuous Air Hissing from Under the Cab Floor / Exhaust Port: Worn internal O-rings or damaged inlet/exhaust poppet seats leaking compressed air when the pedal is either released or depressed.

    2. Stiff, Spongy, or Sticking Brake Pedal Return: Corroded pedal hinge pin, torn dust boot allowing mud ingress, or swollen piston seals preventing smooth pedal modulation and full release.

    3. Delayed Brake Application or Uneven Front/Rear Braking: Imbalanced primary/secondary piston travel causing sluggish pressure buildup or premature wheel lockup on one axle.

    4. Air Leakage at Pre-Fitted Pipe Joints or Stripped Fitting Threads: Cracked fittings or fatigued seals at the valve-to-chassis pneumatic line connections.

    Best Practices for Installation & Pneumatic Cab Control Servicing

    To ensure crisp pedal modulation and airtight pneumatic connections when installing the 3514010-D9860W brake valve with pipe joint assembly and pedal:

    • Depressurize Air Tanks & Tag Chassis Brake Lines Before Removal: Drain all air reservoirs completely before disconnecting lines from the old valve, and label primary supply, secondary supply, and delivery lines so they connect to the exact matching ports on the 3514010-D9860W pipe joint assembly.

    • Clean Cab Floor Mounting Flange & Verify Pedal Clearance: Remove rust, old gasket residue, and floor mat obstructions around the cab mounting opening so the pedal travels cleanly from full release to full stroke without binding.

    • Charge System & Perform Leak and Graduated Pressure Checks: Build full air pressure (8–10 bar), spray soapy water across all pipe joints and the valve exhaust port in both released and applied positions to verify zero bubbles, and test smooth progressive braking prior to road dispatch.

    Frequently Asked Questions (FAQ)

    Q1: Does part number 3514010-D9860W include both the foot pedal and the pneumatic pipe joints?Answer: Yes. Part number 3514010-D9860W is supplied as a complete ready-to-install module including the foot brake pedal treadle, dual-circuit brake valve body, and pre-fitted pipe joint assembly for FAW Jiefang heavy-duty trucks.

    Q2: Is the 3514010-D9860W brake valve tested before shipment?Answer: Yes, every 3514010-D9860W assembly undergoes pneumatic bench testing prior to export to verify dual-circuit pressure balance, smooth pedal graduation, rapid exhaust venting, and zero air leakage.

    Q3: How is this 8.0 kg brake valve and pedal assembly packaged for international wholesale orders?Answer: Each 8.0 kg unit is fitted with protective dust caps on every pipe joint, sealed in a protective poly bag, cushioned with molded foam inserts, and packed inside a sturdy 25 x 20 x 30 cm neutral export carton box for safe air freight or palletized ocean shipping.

    Q4: What are the MOQ, warranty coverage, payment terms, and delivery lead times for B2B buyers?Answer: We support flexible procurement starting from a 1-piece MOQ up to bulk distributor orders. Every unit includes a 6-month warranty, with payments accepted via T/T, Western Union, PayPal, and MoneyGram, and dispatch completed within 3 to 7 days from Shandong, China.



    WG9719584011 Genuine Sinotruk HOWO Light SwitchWG9719584011 Genuine Sinotruk HOWO Light SwitchWG9719584011 Genuine Sinotruk HOWO Light SwitchWG9719584011 Genuine Sinotruk HOWO Light Switch

    Send Inquiry
    Contact Info
    X
    We use cookies to offer you a better browsing experience, analyze site traffic and personalize content. By using this site, you agree to our use of cookies. Privacy Policy
    RejectAccept